![]() Remove the pump from the washer fluid reservoir with a twisting/pulling motion. Disconnect the pump's electrical connector. Disconnect the supply tube from the pump. It is on the lower-left side of the washer fluid reservoir. Chock the rear wheels.Ĭrawl underneath the front of the vehicle, and locate the washer fluid pump. Raise the front of the vehicle with the automotive jack, and support it with jack stands. Engage the parking brake, and open the hood. Shut down the engine, and place the Civic's transmission in "Park" (automatic transmission) or first gear (manual transmission). How to Replace the Windshield Washer Pump on a Honda Civic Unfold the fender and replace the two bolts you removed earlier. Reattach the hose to the nipple of the pump and the connector to the socket of the pump. Spray some WD40 onto the grommet and insert the washer pump over the grommet, snapping the pump underneath the tabs of the washer reservoir. Insert the grommet from the new pump into the washer reservoir. Stick the head of the pick under the flange, or lip, of the grommet, and pry the grommet off in one swift motion.Ĭompare the old windshield washer pump to the new one, checking that the height and girth, the number of pins in the socket for the connector, and the location of the nipple are all the same. Use your pick to pry off the plastic washer-pump grommet mounted where the pump was attached to the washer reservoir. Use some force to pull the pump straight out of the reservoir. The shape of the washer reservoir itself holds the pump in place. Pull the pump off of the washer reservoir. The hose and nipple are located opposite the connector on the washer pump. Pull the washer hose off the nipple of the washer pump. Pull firmly, but do not jerk the connector off or you may break it. The connector brings electrical power to the pump a small black cylinder crouched against the white body of the reservoir. Pull off the windshield-washer pump connector by gripping it and pulling firmly upward. This reveals the windshield-washer reservoir and the washer pump attached to it. Pull the fender in toward the wheel and tuck it out of the way when the bolts are removed. Use your socket wrench to remove these bolts, which sit horizontally in the wheel well. ![]() Remove part of the front passenger-side fender by taking off two of the bolts attaching the fender to the vehicle. How to Replace the Windshield Washer Pump on a 19 Refill the washer fluid reservoir and check the windshield washer pump's operation. Set your 3/8-inch drive torque wrench to 12 ft-lbs. ![]() Connect the cable back to the battery and tighten its bolt by hand until snug. Remove the tape on the negative battery terminal. and completely tighten both of the bolts. Set your 1/4-inch drive torque wrench to 60 in-lbs. Reconnect the push-on power wire to the fluid reservoir and thread both of the reservoir’s mounting bolts by hand. The hose simply pushes back on-no tools required. Before you return its mounting bolts, reconnect the rubber hose from the pump back to the nipple on the bottom of the reservoir. Insert the fluid reservoir down into position ready for mounting. Mount the new pump into position on the firewall and wiggle it while pushing inward until you see it fully seated against the firewall. Your new washer pump will come with a new grommet and fluid hose, so you don’t have to save either from the old pump.Īttach the fluid hose and grommet to your new washer pump if it wasn’t already pre-assembled. It’s held in place by a large rubber grommet that mounts on a nipple on the side of the pump. The pump doesn’t have any bolts holding it to the firewall. Place the two bolts in your pocket for safekeeping and set the reservoir to the side of the work area.ĭisconnect the wiring harness plug connected to the washer pump by hand, and then wiggle the pump away from the firewall to free it. Remove the two mounting bolts on the left side of the reservoir and lift the reservoir out of the car. Pull the hose off the reservoir and allow any remaining washer fluid to drain into the pan.ĭisconnect the small push-on power wire from the reservoir by pulling it straight off its connection. Reach down beneath the reservoir and feel for a rubber hose connected to the its bottom. Open the filler cap on the washer fluid reservoir. Slide a drain pan under the car directly in line with the washer fluid reservoir. Once you have removed the cable, use a roll of electrical tape to wrap the metal terminal at the end of the cable, then position it away from the battery. ![]() To identify which of the two cables connected to the battery is the negative, look for a small minus sign on top of the battery case next to the cable. Loosen and remove the negative battery cable from its post on the battery with a socket wrench. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |